JIS C6560-1994 同心插头、插座
时间:2024-05-06 22:24:16 来源: 标准资料网 作者：标准资料网 阅读：8895
【英文标准名称】:Concentricplugsandjacks
【原文标准名称】:同心插头、插座
【标准号】:JISC6560-1994
【标准状态】:现行
【国别】:日本
【发布日期】:1994-03-01
【实施或试行日期】:
【发布单位】:日本工业标准调查会(JP-JISC)
【起草单位】:TechnicalCommitteeonElectronics
【标准类型】:()
【标准水平】:()
【中文主题词】:电子设备及元件;插座;同心;电插头;插头适配器;插塞
【英文主题词】:concentric;;;;;
【摘要】:この規格は,電子機器の回路接続のために使用する超小形単頭プラグ,小形単頭プラグ及び大形単頭プラグとそれらに適合するジャックについて規定する。
【中国标准分类号】:L24
【国际标准分类号】:31_220_10
【页数】:22P;A4
【正文语种】:日语
Product Code:SAE J1113/3
Title:Conducted Immunity, 250 kHz to 400 MHz, Direct Injection of Radio Frequency (RF) Power (Cancelled Aug 2010)
Issuing Committee:Electromagnetic Compatibility (Emc) Standards
Scope:This part of SAE J1113 specifies the direct RF power injection test method and procedure for testing electromagnetic immunity of electronic components for passenger cars and commercial vehicles. The electromagnetic disturbances considered in this part of SAE J1113 are limited to continuous, narrowband conducted RF energy. This test method is applicable to all DUT leads except the RF reference ground. The test provides differential mode excitation to the DUT. Immunity measurements of complete vehicles are generally only possible by the vehicle manufacturer. The reasons, for example, are high costs of a large absorber-lined chamber, preserving the secrecy of prototypes or the large number of different vehicle models. Therefore, for research, development, and quality control, a laboratory measuring method for components shall be applied by the manufacturer. This method is suitable over the frequency range of 250 kHz to 400 MHz. This direct RF power injection test is particularly effective when used as part of the engineering development of the electronic component (at the prototype PCB level) where the line by line diagnostic capabilities of this test facilitate cost-effective circuit board level improvements in the RF immunity performance of the module or component【英文标准名称】:Pneumaticfluidpower-Directionalcontrolvalves-Measurementofshiftingtime
【原文标准名称】:气动方向控制阀切换时间的测量
【标准号】:ISO12238-2001
【标准状态】:现行
【国别】:国际
【发布日期】:2001-07
【实施或试行日期】:
【发布单位】:国际标准化组织(IX-ISO)
【起草单位】:ISO/TC131
【标准类型】:()
【标准水平】:()
【中文主题词】:气动设备;圆孔测试量规;电磁阀;分配阀门;流体技术;名称与符号;气动传动系统;阀门;气动力学;液压传动;液压传动系统;设计;方向控制阀;测量技术;尺寸;配件;定义;定义
【英文主题词】:Definitions;Design;Designations;Dimensions;Direction-controlvalves;Distributingvalves;Fittings;Fluidtechnology;Hydraulicfluidpower;Hydraulictransmissionsystems;Magneticvalves;Mastergaugeforholes;Measurement;Measuringtechniques;Operatingtime;Pneumaticequipment;Pneumatictransmissionsystems;Pneumaticvalve;Pneumatics;Testing;Valves
【摘要】:本标准规定了电控或气控方向控制阀和逻辑元件的切换时间的定义、测量方法以及测试结果报告的方法,以便气动系统应用。
【中国标准分类号】:J16
【国际标准分类号】:23_100_50
【页数】:12P.;A4
【正文语种】:英语